Clear or transparent oil-wax combination for treating furniture and kitchen worktops made of wood. Osmo TopOil is based on natural plant oils and waxes. Suitable for wood; microporous surface will not crack, peel, flake or blister. Resistant against wine, beer, cola, coffee, tea, fruit juice, milk and water in accordance with German DIN 68861-1A – no water spots. The dry finish is safe for humans, animals and plants (resistant to saliva and perspiration acc. German DIN 53160, suitable for children‘s toys acc. EN 71.3).Osmo TopOil is food safe acc. EN 1186 Part 5 / 14.
INGREDIENTS
Based on natural plant oils (sunflower oil, soya oil, thistle oil) and waxes, paraffin, pigments, lead-free siccatives (drying agents) and water-repellent additives. Dearomatized white spirit (benzene-free). VOC classification in compliance with EU regulations (2004/42/EC): out of scope. Detailed declaration of ingredients available upon request.
STORAGE
Up to 5 years and longer if container is kept dry and closed tightly. If thickened by frost, store for 24-36hours at room temperature before use.
SURFACE PREPARATION
Wood surface must be clean, dry and frost-free (moisture content max. 18%). Osmo TopOil is ready to use. Do not thin. Stir well before use.
Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.
Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler). Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for furniture and worktops P150-240 (depending on wood species – for worktops max. P150).
Before oiling the surface, remove sanding dust with a broom or vacuum cleaner. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar
surfaces.
METHODS OF APPLICATION
Apply the first coat thinly along the wood grain with an Osmo Microfibre Roller, Flat Brush or Oil Finish Applicator Fleece.
Allow to dry for approx. 8-10 hours. Ventilate well while drying.
Apply the second coat with an Osmo Oil Finish Applicator Fleece or a lint-free cloth.
For renovations, one coat applied to the clean and dry surface with an Oil Finish Applicator Fleece or lint-free cloth is usually sufficient.
TOPOILHIGH SOLID
Oil-wax wood finish
1COAT
24 m²/1l
RECOMMENDED USE
Osmo TopOil is ideal for the protection of furniture surfaces and work surfaces made of solid wood or edge-glued panels (e.g. kitchen worktops, desks,
shelving etc.) in indoor areas. Also suitable for cork and OSB.
SURFACE PREPARATION
Wood surface must be clean, dry and frost-free (moisture content max. 18%). Osmo TopOil is ready to use. Do not thin. Stir well before use.
Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.
Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler). Sand wood surfaces carefully. Begin with coarse sandpaper then progress to finer grades– final sanding work for furniture P150-240 (depending on wood species ). For kitchen work tops using absorbent hardwoods like Oak or Beech, final sanding grade P120. For very absorbent woods like Pine, sand to a maximum of P150.
For dark and extractive-rich woods (e.g. Iroko, Teak, Mahogany, Sapele, Wenge, Merbau, Jatoba, Cedar etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.
Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
Reviews
There are no reviews yet.